(Press-News.org) A Northwestern University team has confirmed a new way to help the airline industry save dollars while also saving the environment. And the solution comes in three dimensions. By manufacturing aircrafts' metal parts with 3-D printing, airlines could save a significant amount of fuel, materials, and other resources.
Led by Eric Masanet, the team used aircraft industry data to complete a case study of the life-cycle environmental effects of using 3-D printing for select metal aircraft parts, a technique that is already being adopted by the industry. The team concluded that 3-D printing the lighter and higher performance parts could significantly reduce both manufacturing waste and the weight of the airplane, thus saving fuel and money and decreasing carbon emissions.
Funded by the US Department of Energy's Advanced Manufacturing Office, the case study is described in a paper published in the May issue of the Journal of Cleaner Production. Runze Huang, a graduate student in Masanet's lab, is first author of the paper. Other authors include Matthew Riddle and Diane Graziano from Argonne National Laboratory.
"The airline industry is an early adopter of 3-D printing," said Masanet, the Morris E. Fine Junior Professor in Materials and Manufacturing at Northwestern's McCormick School of Engineering. "The main driver is that aircrafts require specialized lightweight metal alloys that can be very costly to process."
Conventional manufacturing methods tend to be inefficient and wasteful. To produce a 1-kilogram bracket for an airplane, for example, it may require 10 kilograms of raw material input into the manufacturing process. And, from an engineering design perspective, that final bracket may still contain much more metal than is required for the job. 3-D printing, on the other hand, requires far less raw material inputs and can further produce parts that minimize weight through better design.
"We have suboptimal designs because we're limited by conventional manufacturing," Masanet said. "When you can make something in layer-by-layer fashion, those constraints diminish."
Masanet does not anticipate a change to the crucial parts of the aircraft, such as the wings and engine, any time soon. But he does see real potential in the replacement of less flight-critical parts, such as brackets, hinges, seat buckles, and furnishings. According to the case study, 3-D printing a bracket, for example, reduced its weight from 1.09 kilograms to 0.38 kilograms. This might not seem like much, but it adds up.
"There are enough parts that, when replaced, could reduce the weight of the aircraft by 4 to 7 percent," Masanet said. "And it could be even more as we move forward. This will save a lot of resources and a lot of fuel."
If the 3-D components evaluated in the case study are used to their full potential, Masanet predicted it would greatly benefit the environment in more than one way. First, his team estimated that airplane fuel consumption could be reduced by as much as 6.4 percent, reducing both fossil fuel dependency and greenhouse gas emissions. Second, their life-cycle analysis found that manufacturing 3-D printed components uses as little as one-third to one-half of the energy currently used in conventional methods. Manufacturers would also potentially save thousands of tons of aluminum, titanium, and nickel that are otherwise scrapped every year.
But Masanet said there is one caveat. Scientists need to improve 3-D printing technology to realize the full extent of the estimated aircraft weight savings. Limitations in the process, such as issues with surface quality, residual stresses, repeatability, and throughput, are current barriers to full-scale adoption. But Masanet hopes this case study will provide further proof that continued research efforts and funding should be focused on improving the 3-D printing process.
"If we can accelerate the necessary process improvements, then we can start reaping these savings sooner," he said. "Maybe then we can start seeing savings 10 years earlier than if we just let the technology progress at its regular rate."
INFORMATION:
Carnegie Mellon University chemists, led by Mark Bier, have separated and weighed virus particles using mass spectrometry (MS). This is the first time that researchers successfully used matrix-assisted laser desorption ionization MS to analyze a mixture of intact virus particles.
Bier, research professor of chemistry and director of Carnegie Mellon's Center for Molecular Analysis, and graduate student Logan Plath will present their findings in a poster session at the American Society for Mass Spectrometry Conference on Mass Spectrometry and Allied Topics today, June 2, ...
In a clinical study of patients in the United States and China, researchers found that a low-cost, portable, battery-powered microendoscope developed by Rice University bioengineers could eventually eliminate the need for costly biopsies for many patients undergoing standard endoscopic screening for esophageal cancer.
The research is available online in the journal Gastroenterology and was co-authored by researchers from nearly a dozen institutions that include Rice, Baylor College of Medicine, the Chinese Academy of Medical Sciences and the National Cancer Institute.
The ...
BOSTON, MA - Use of antidepressants late in pregnancy has been controversial since the FDA issued a Public Health Advisory in 2006 warning that the use of antidepressants in late pregnancy may increase risk of persistent pulmonary hypertension of the newborn (PPHN), a condition that typically occurs in term or near-term infants and presents within hours of birth with severe respiratory failure requiring intubation and mechanical ventilation. The 2006 public health advisory was based on a single epidemiologic study that found a six-fold increase in risk associated with ...
An analysis of approximately 3.8 million pregnancies finds that use of antidepressants late in pregnancy may be associated with an increased risk of persistent pulmonary hypertension of the newborn (PPHN), according to a study in the June 2 issue of JAMA. However, the absolute risk was small and the risk increase appears more modest than suggested in previous studies. PPHN is a rare but life-threatening condition that occurs when a newborn's circulation system doesn't adapt to breathing outside the womb.
Persistent pulmonary hypertension of the newborn is associated with ...
Implementation of a pre-surgical intervention that included screening for the bacteria Staphylococcus aureus, treating patients who were positive for this bacteria, and the administration of antibiotics based on these culture results was associated with a modest reduction in S. aureus surgical site infections, according to a study in the June 2 issue of JAMA.
S. aureus carriage increases the risk of S. aureus surgical site infections (SSIs). The risk for these infections may be decreased by screening patients for nasal carriage of S. aureus and decolonizing carriers ...
An analysis of the use of computerized clinical decision support systems regarding orders for advanced diagnostic imaging found that the systems failed to identify relevant appropriateness criteria for the majority of orders, according to a study in the June 2 issue of JAMA.
Computerized clinical decision support (CDS) systems that match patient characteristics against appropriateness criteria to produce algorithmic treatment recommendations are a potential means of improving care. The Protecting Access to Medicare Act of 2014 mandates use of CDS systems for the ordering ...
Using tools that help physicians decide whether to use expensive imaging studies such as MRI scans can help reduce the ordering of unnecessary tests, but implementation of the tools in real-world settings has many challenges, according to a new RAND Corporation study.
The tools, computer-based programs that match a patient's characteristics against treatment criteria and recommend a treatment, helped increase the proportion of tests for Medicare fee-for-service patients rated as appropriate, according to findings published in the June 2 edition of the Journal of the American ...
This news release is available in French. Montreal, June 2nd, 2015 - A team of researchers from Universite de Montreal, Polytechnique Montreal and the Centre national de la recherche scientifique (CNRS) in France is the first to succeed in preventing two-dimensional layers of black phosphorus from oxidating. In so doing, they have opened the doors to exploiting their striking properties in a number of electronic and optoelectronic devices. The study's results were published in the prestigious journal Nature Materials.
Black phosphorus: future key player in new technologies
Black ...
Any box or bottle of over-the-counter (OTC) medicine lists its active ingredients prominently on the label. But are consumers using that information to make wise choices about taking two or more OTC drugs at the same time? Probably not, suggests a new study in the Journal of Public Policy & Marketing.
"A consumer who takes a cold medicine containing, for instance, acetaminophen, may see nothing wrong with taking an additional medicine that also contains acetaminophen," write authors Jesse R. Catlin (California State University, Sacramento), Connie Pechmann (University ...
You go to the grocery store to buy a pound of ground beef and a can of tomato sauce. You walk out with the ground beef, the sauce, and a bag of chocolate-covered almonds, a silicon spatula, and the latest celebrity magazine. What happened? According to a new study in the Journal of Marketing, what and when you purchased determined the array of items you eventually bought.
"Shoppers enter the grocery store planning to buy certain things, but are tempted to buy unplanned items," write authors Timothy J. Gilbride (University of Notre Dame), Jeffrey Inman (University of Pittsburgh), ...
