Turning carbon dioxide into fuel just got easier, thanks to acid bubbles

(Press-News.org) A team of researchers at Rice University have discovered a surprisingly simple method for vastly improving the stability of electrochemical devices that convert carbon dioxide into useful fuels and chemicals, and it involves nothing more than sending the CO 2 through an acid bubbler.

Their study, published in Science, addresses a major bottleneck in the performance and stability of CO 2 reduction systems: the buildup of salt that clogs gas flow channels, reduces efficiency and causes the devices to fail prematurely. Using a technique they call acid-humidified CO2, the researchers extended the operational life of a CO 2 reduction system more than 50-fold, demonstrating more than 4,500 hours of stable operation in a scaled-up reactor — a milestone for the field.

Electrochemical CO 2 reduction, or CO2RR, is an emerging green technology that uses electricity, ideally from renewable sources, to transform climate-warming CO 2 into valuable products like carbon monoxide, ethylene or alcohols. These products can be further refined into fuels or used in industrial processes, potentially turning a major pollutant into a feedstock.

However, practical implementation has been hindered by poor system stability. One persistent issue is the accumulation of potassium bicarbonate salts in the gas flow channels, which occurs when potassium ions migrate from the anolyte across the anion exchange membrane to the cathode reaction zone and combine with CO 2 under high pH conditions.

“Salt precipitation blocks CO 2 transport and floods the gas diffusion electrode, which leads to performance failure,” said Haotian Wang , the corresponding author of the study and associate professor of chemical and biomolecular engineering, materials science and nanoengineering and chemistry at Rice. “This typically happens within a few hundred hours, which is far from commercial viability.”

To combat this, the Rice team tried an elegant twist on a standard procedure. Instead of using water to humidify the CO 2 gas input into the reactor, they bubbled the gas through an acid solution such as hydrochloric, formic or acetic acid.

The vapor from the acid is carried into the cathode reaction chamber in trace amounts, just enough to alter the local chemistry. Because the salts formed with these acids are much more soluble than potassium bicarbonate, they don’t crystallize and block the channels.

The effect was dramatic. In tests using a silver catalyst — a common benchmark for converting CO 2 to carbon monoxide — the system operated stably for over 2,000 hours in a lab-scale device and more than 4,500 hours in a 100-square-centimeter, scaled-up electrolyzer. In contrast, systems using standard water-humidified CO 2 failed after about 80 hours because of salt buildup.

Importantly, the acid-humidified method proved effective across multiple catalyst types, including zinc oxide, copper oxide and bismuth oxide, all of which are used to target different CO2RR products. The researchers also demonstrated that the method could be scaled without compromising performance with large-scale devices maintaining energy efficiency and avoiding salt blockage over extended periods.

They observed minimal corrosion or damage to the anion exchange membranes that are typically sensitive to chloride by keeping the acid concentrations low. The approach was also shown to be compatible with commonly used membranes and materials, reinforcing its potential for integration into existing systems.

To observe salt formation in real time, the team used custom-built reactors with transparent flow plates. Under conventional water humidification, salt crystals began forming within 48 hours. With acid-humidified CO2, however, no significant crystal accumulation was observed even after hundreds of hours, and any small deposits were eventually dissolved and carried out of the system.

“Using the traditional method of water-humidified CO 2 could lead to salt formation in the cathode gas flow channels,” said co-first author Shaoyun Hao, postdoctoral research associate in chemical and biomolecular engineering at Rice. “We hypothesized — and confirmed — that acid vapor could dissolve the salt and convert the low solubility KHCO 3 into salt with higher solubility, thus shifting the solubility balance just enough to avoid clogging without affecting catalyst performance.”

The work opens the door to more durable, scalable CO 2 electrolyzers, a critical need if the technology is to be deployed at industrial scales as part of carbon capture and utilization strategies. The simplicity of the approach, involving only small tweaks to existing humidification setups, means it can be adopted without significant redesigns or added costs.

“This is a major finding for CO 2 electrolysis,” said Ahmad Elgazzar, co-first author and graduate student in chemical and biomolecular engineering at Rice. “Our method addresses a long-standing obstacle with a low-cost, easily implementable solution. It’s a step toward making carbon utilization technologies more commercially viable and more sustainable.”

This work was supported by the Robert A. Welch Foundation, Rice, the National Science Foundation and the David and Lucile Packard Foundation.

END